POLYBOND Polybond Limited, Unit 6 William Street, Northam, Southampton, Hants. S014 5QH Tel: 023 80 223266 Fax: 08700 527587

1. Substance/Preparation & Company Identification

   1. Chemical Nature: A blend of zircon sands, clays and fluxes which is mixed with water prior to application.
   2. Company: As above.



2. Main Constituents

   1. Contains: Zirconium Silicate, Special Clays, Fluxes.
   2. EEC Symbol:
   3. R Phrases:



3. Hazard Identification Occupational exposure limits quoted are those for zirconium compounds in H.S.E. guidance note EH40/94. Furnascote also contains 0.2% of free silica and must therefore be treated as nuisance dusts. Exposure limits are: 10 mg/m³ total inhalable dust, short term exposure limit, 10 minute ref; 5 mg/m³ respiable dust, long term exposure will be 8 hours TWA.
   Mixing with water during application eliminates these hazards.

4. First Aid Measures

   1. Skin Contact: Wash off with soap and plenty of water.
   2. Eye contact: Flush eyes with plenty of clean water for at least 15 minutes.
   3. Inhalation: No action required
   4. Ingestion: Non toxic no action required.



5. Fire Fighting Measures Fibrecote is non-flammable.

   2. Extinguishing Media: N/A
   3. Unsuitable Extinguishing Media: N/A
   4. Exposure Hazards: N/A
   5. Additional Information: N/A



6. Accidental Release Measures

   1. Personal Precautions: Wear a dust mask if sweeping up powder spillage.
   2. Environmental Precautions: N/A
   3. Methods for Cleaning: Clean up powder spillages by sweeping or vacuming taking care not to generate dust. (Dampen down with water first if possible). Place in labelled closed containers to await disposal.



7. Handling and Storage Use local exhaust ventilation and filtration plant to control dusts. Operators should wear dust masks when handling Furnascotes in their dry powder form.

   1. Handling: Provide good ventilation if using indoors. All equipment should be flame proof .Avoid all contact with skin and eyes. Keep all containers away from all sources of ignition. If spraying, wear suitable respiratory equipment.
   2. Storage: Store under dry conditions to preserve quality.



8. Exposure Controls/Personal Protection

   1. Limits: Dust extraction and ventilation at source.
   2. Respiratory Protection: Wear dust masks when handling the dry powder forms.
   3. Hand Protection: Wear plastic or industrial rubber gloves.
   4. Eye Protection: Safety goggles to BS 2092 should be worn.
   5. Skin Protection: Keep skin covered use barrier creams.
   6. Engineering Measures:



9. Physical and Chemical Properties

   Appearance:	Free Flowing Cream Powder
   Odour:	None
   Boiling Point:
   Density:	4.5g/cm³
   Flashpoint:	40°C Abel
   Melting Point:	Approx 2000°C
   Ignition:
   Solubility in Water:	Approx. 5%
   pH Value:	Neutral
   Vapour Pressure:
   Viscosity:

10. Stability and Reactivity Fibrecote can be considered inert.

    1. Thermal Decomposition:
    2. Conditions to Avoid:
    3. Hazardous Decomposition:



11. Toxicological Information on Mixed Liquid Material

    1. No Reported acute or chronic effects.
    2. Eye Contact:
    3. Skin Contact:
    4. Ingestion:
    5. Inhalation:

12. Ecological Information

    1. Fibrecote is almost insoluble and are unlikely to contaminate water or enter food chains in the quantities usually supplied.

13. Disposal Considerations

    1. Dispose of as land fill/



14. Transport Information

    1. No special precautions are necessary.

15. Regulatory Information No special hazard labelling is required.

    1. Classification Symbol:
    2. Risk Phrases:
    3. Safety:



16. Other Information None

This product should be stored and handled in accordance with good industrial hygiene practice and in conformity with any legal regulation. This information is to our best of knowledge correct and given in good faith but without warranty. It remains the users responsibility to ensure the information is appropriate for any particular use of the product.

Polybond Health and Safety