Quickfloor
Epoxy Floor Paint

Product Information

A full-bodied epoxy paint for a tough, attractive and long lasting finish to most floor surfaces. Polybond Quickfloor will withstand arduous industrial / commercial pedestrian and vehicular traffic. It is easy to keep clean, resists scuffing and marking keeping a good decorative finish for many years.

• Water-based, non flammable and non-hazardous.
• Use on concrete, masonry, asphalt and wood.
• Economical and versatile … one or two coats to suit requirements.
• Can be applied to damp surfaces.
• Easy to apply by roller or brush.
• Little smell and ideal for use in factories … no need for shut down.

Ideal for workshops, factories, warehouse, garages, showrooms, farm buildings, conservatories, changing rooms, toilets, pool surrounds, cellars, shops and food premises etc.

• Long Pot Life.
• Clean rollers etc. in water after use.
• Dries hard overnight. Fully cured in 5 to 6 days.
• Resists oils, petrol and most common chemicals.
• Provides a waterproof barrier on damp concrete.
• Dries to an attractive low-gloss finish in a basic colour range.
• A high gloss finish is available.

Perparation

Quickfloor should only be applied to sound, clean, grease-free surfaces. Pot holes and cracks should be repaired before painting. Quickfloor must not be applied where there is a risk of running water, heavy condensation or temperatures below 5°C. Bare concrete and other porous substrates must be primed.
Prime only with Quickfloor Clear when:

1. The concrete is damp.
2. The finished floor will be subjected to heavy contamination with liquids or chemicals.
3. The most durable job is required.

Alternatively, dry concrete intended for light industrial use need only be primed with Polybond PVA or similar, diluted with 4 to 5 parts of water, depending on porosity.

After priming, one coat of Quickfloor finish in the desired colour will give an acceptable result at minimum cost. Apply two coats on areas of high wear or when the most durable job is required. For a really glossy finish, apply a topcoat of Quickfloor Clear over the colour. Previously coated surfaces in sound condition will not need priming; just one or two coats of the finish.

Mixing

Quickfloor is a two-component product. Base and hardener are supplied in matched quantities and must be thoroughly mixed together before use. Do not attempt to split the packs. Mixed material has a pot life and must be used immediately.

Application

By short pile lambswool roller. Allow overnight of six to twelve hours between coats. Wash equipment in cold water at 1 hours intervals.

Drying

Quickfloor will accept light traffic after approximately 24 hours at 15°C and will be fully cured in 3 to 4 days at 15°C. These times will vary according to temperature.

Non-Slip Surfaces

Cast an excess of grit into the first coat of Quickfloor whilst freshly wet. Leave overnight then sweep away loose grit. Using a fairly stiff brush, apply another coat to encapsulate.

Coverage

On smooth surfaces of average porosity approximately 10m² per litre of Clear and 8m² per litre for the finish. When coating over grit allow around 5m² per litre.

Specifications

Availability	Clear, Grey (18-B-21), Dark Grey (18-B-25), Dark Green (14-C-39) and Tile Red. 2.5 litre tubs
Minimum Cure Temperature	5°C under low humidity. 8°C under normal humidity.
Touch Dry	6 hours at 15°C. 12 hours at 8°C.
Recoat	6 to 12 hours according to temperature.
Pot Life	2.5 hours at 7 to 10°C. 1.5 hours at 15 - 20°C.
Full Cure	3-4 days at 15°C. 2 to 3 days at 15 - 20°C.
Storage Life	Unopened Quickfloor has a storage life of fifteen months from delivery when stored below 15°C.

Health and Safety

Barrier creams and rubber gloves should be worn when using Quickfloor. Wear goggles to protect eyes from splashes. Ensure good ventilation during application.

Product Reference No : Q/F Amendment date August 2002

Makes wet surfaces safer to walk on

The claims made in this document are made in good faith and are based on exhaustive tests carried out over a long period.
Polybond Ltd., their agents and their distributors cannot accept any liability for the behaviour of their materials in individual cases.

A printer friendly copy is available here

A Health and Safety Reference Datasheet is available here